Page Symptoms And Actions 0. Plug in the Ethernet cable. To enter the ". Page battery removal when a call is disconnected. However, the Cisco ATA can be configured to reverse the voltage polarity when a call is connected or disconnected.
Page Contacting Tac Customers who obtained their equipment through service providers, independent dealers and other third parties must contact their equipment provider for technical assistance. Page Appendix OL —Use this parameter to enable desired features. Page Caller Id Step 6 additional person, that new person can then call someone else, and so on.
This is known as daisy-chaining. This feature is disabled when you hang up. Page Physical Interfaces nF complex impedance. Enhanced fax pass-through is supported on the Cisco ATA. Page Appendix H. Page 3w2d: 3w2d: 3w2d: terminalAlias 3w2d: 3w2d: hID :"" 3w2d: 3w2d: gatekeeperIdentifier "cgk. Figure D-2 H. Local H. Two-way communication ensues between endpoints over the H. Page : t35CountryCode t35Extension 0 manufacturerCode data 'B This scenario assumes that the H. Page Q. Call setup initiates from the local H.
Gateway acknowledges call setup initiation. Page t35Extension 0 manufacturerCode data 'AA Page Compare with compression and expansion. Page A firewall router uses access lists and other methods to ensure the security of the private network. Page Network Time Protocol. Protocol built on top of TCP that assures accurate local time-keeping with reference to radio and atomic clocks located on the Internet.
This protocol is capable of synchronizing distributed clocks within milliseconds over long time periods. Page Signaling connection control part. Page Voice activity detection. When enabled on a voice port or a dial peer, silence is not transmitted over the network, only audible speech. When VAD is enabled, the sound quality is slightly degraded but the connection monopolizes much less bandwidth.
Page Markup Language. XML allow you to define your own customized markup language. Page proxy server standard terminals H. Page No. This manual is also suitable for: Ata Set bits of the OpFlags parameter to 1, 0, and 1, respectively. This setting translates to the following Page Using Atapname. This is the name you use for the unique Cisco ATA binary configuration file. The following command and output show an example of this command. If input-text-file sets the Cisco ATA EncryptKey parameter to a nonzero value and the -e option is used, then output-binary-file is encrypted with the EncryptKey parameter set in input-text-file and Secret is ignored.
Page Atadefault. You can also use the voice configuration menu if you need to configure a small number of parameters or if the web interface and TFTP configuration are not available.
You should receive Step 2 the initial voice configuration menu voice prompt. Page Entering Alphanumeric Values Step 5 automatically timeout after 10 seconds. Cisco strongly recommends that you set a password.
Use the voice menu code SETPASS to Step 6 configure a password through the voice configuration menu, after which you are prompted for the password whenever you attempt to change a parameter value. Page 53 Do not use the web configuration page to attempt to change any values that you configured by means of Note the TFTP configuration file method.
By opening a web page for the Cisco ATA, you can perform a refresh before the scheduled refresh. Do not use it. The Cisco ATA can use up to four media ports to handle conference calls on both lines. For example, if media base port is used for one call, the next call uses port and other calls will use ports and Page Network Timing If the backup proxy fails, the Cisco ATA automatically switches back to the primary proxy if the unit has been using the backup proxy for at least 30 seconds.
This effectively prevents the Cisco ATA from switching indefinitely between failing primary and failing backup proxies for the same transactions. Both the interval and total time can be specified by the user. DNS results are hard-coded in cache memory for 10 minutes. Page Configuration Text File Template You can make a copy of this file and use it as a template for creating your own default configuration file or Cisco ATA-specific configuration file.
Page User Interface Ui Parameter To clear a password, change the value to 0. If you forget a password, you can contact your Cisco representative. Value Type If the value is set to zero, the port will be disabled and no dial tone will sound. Page Pwd1 For an IP address, a '.
For a URL, a ':' must be used to indicate a port. Re-registration does not occur until the current registration period expires. The Cisco ATA renews the registration at some percentage of time earlier than the specified interval to prevent a registration from expiring. This parameter must be an even number.
Each connection uses the next available even-numbered port for RTP. Page Natserver For IP addresses, a period. For a URL, a colon : must be used to indicate a port.
If no port parameter is specified, the port is assumed. Page Nattimer 0, which means that no dummy packets will be sent to the NatServer. When G. Page Rxcodec 1—G. Fax mode. For Fax mode, use For Fax mode, use the following settings: G. Page Featuretimer Bits —On-hook delay before a call is disconnected. The user can hang up the phone in one room and pick up the phone in another room without disconnecting the line.
Page Connectmode 0—Use fax pass-through. If this bit is disabled, the Cisco ATA forwards the entire dial string, including service activation code, to the SIP proxy for processing. NTPIP is ignored if its value is 0 or 0. The user must not specify a port parameter. Page Udptos This parameter controls various timeout values. Table on page contains bit definitions of this parameter. In addition, the Cisco ATA obtains its configuration file during the bootload process.
The following list summarizes the default Cisco ATA behavior during its boot-up process:. If your network environment is not set up to handle this default behavior, make the necessary configuration changes by referring to the. For a list of parameters that you must configure to obtain network connectivity, se e.
0コメント